(de) Verwenden der 3D-CAD-Symbolleiste

Mit den Schaltflächen und Optionen der 3D-CAD-Symbolleiste können Sie ein 3D-CAD-Bild für jede von Ihnen erstellte Ansicht bearbeiten. In der folgenden Tabelle finden Sie Einzelheiten zu den Schaltflächen und Optionen der Symbolleiste. 3D CAD toolbar

Wichtig!

Wenn Sie die Optionen der Symbolleiste nutzen, beachten Sie bitte, dass Änderungen nicht rückgängig gemacht oder weiderholt werden können, wenn Sie ein 3D-CAD-Bild verändern. Sie können jedoch Elemente löschen, die Sie dem Bild hinzugefügt haben (z.B. Markierungen). Dies gilt solange die Symbolleistenoption ausgewählt bleibt. Am besten stellen Sie sicher, dass die Master-Ansicht der 3D-CAD-Baugruppe unverändert bleibt, damit Sie bei Bedarf zu ihr zurückkehren können.

Schaltfläche	Name	Beschreibung
	Kamera zurücksetzen	Nachdem Sie die Größe eines 3D-CAD-Bildes geändert haben, wählen Sie Kamera zurücksetzen, um das Bild auf seine vorherige Größe zurückzusetzen.
	Kamera-Menü	Verwenden Sie die Optionen des Kameramenüs, um die Kamera in einer isometrischen, orthographischen oder perspektivischen Projektion oder nach einer ausgewählten Baugruppenfläche auszurichten. Isometrische Ansicht - Dies ist eine Seitenansicht der 3D-Baugruppe (von oben, unten, Vorderseite, Rückseite.) Orthographische Projektion - Bei dieser Ansicht handelt es sich um die Einzelansicht einer Baugruppe (z. B. eine Ansicht der Vorderseite) auf eine Zeichenfläche, bei der die Projektionslinien senkrecht zur Zeichenfläche verlaufen. Perspektivische Projektion - This view uses a planar (two-dimensional) surface to graphically display a 3D assembly to approximate actual visual perception. Left View - This view displays the assembly from the left side. Right View - This view displays the assembly from the right side. Bottom View - This view displays the assembly from the bottom. Front View - This view displays the assembly from the front. Back View - This view displays the assembly from the back. Top View -This view displays the assembly from the top. The Camera Menu options (from left to right, top to bottom) are shown in the following illustration. While working in the Process Definition window, you can hover over each option to view its name.
	Shaded With Lines	Use the Shaded With Lines options to change the look of your 3D assembly image for specific views with shading and lines. There's also an XRay view that displays an assembly as if you were looking through all its layers. The options (from top to bottom) are: Shaded With Lines - Displays the 3D CAD image with shading and definition lines applied. Shaded - Displays the 3D CAD image with shading applied, but no defining lines. Hidden Line - Displays the 3D CAD image with all hidden lines displayed. Wireframe - Displays the 3D CAD image as a wireframe (no solid surfaces are displayed). XRay - Displays the 3D CAD image with all hidden lines displayed, but blurred (similar to an X-ray).
	Redline Note	The Redline Note toolbar button has options that allow you to add redline shapes and notes/annotations to a 3D CAD assembly to call out specific areas of the assembly that operators should pay specific attention to. The available options (from left to right, top to bottom) are: Redline Circle - Drag a circle around the area of the assembly you want to draw attention to. Redline Rectangle - Drag a rectangle around the area of the assembly you want to draw attention to. Redline Note - Displays a notes box where you can add notes to highlight part of an assembly. You can resize the Notes box by dragging the handle in the lower-right corner of the box. Redline Freehand - Displays a freehand "pen" cursor you can use to draw redline freehand shapes on an assembly. Important! If you make a mistake, select the Redline item and press the Delete key to remove it from the CAD image—you can delete the item only as long as the corresponding Redline command is still selected on the toolbar.
	Select Parts	The Select Parts toolbar button (the cursor) allows you to select individual parts in a 3D CAD image. When you select a part, it is highlighted with either Red or Green. Additional options allow you to measure angles or distances between part faces, point-to-point measurements, edge measurements, select areas of the assembly, and create push-pin style notes to call out specific areas where you want to add specific instructions. The options for the Select Part button are (from left to right, top to bottom): Create Note-Pin - Creates a pushpin-style note to call out specific areas or parts on a 3D CAD image. Measure Angle Between Faces - Measures the angle between two part faces. Drag the cursor to select the faces to measure. Measure Distance Between Faces - Measures the distance between two part faces. Drag the cursor to select the faces to measure. Measure Edges - Measures the distance between two part faces. Drag the cursor to select the faces to measure. Measure Point to Point - Measures the distance between two edges on an assembly. Drag the cursor to select the edges to measure. Area Select - Measures the distance between two part faces. Drag the cursor to select an area of the assembly to measure. Important! While using any of the measurement tools (Point to Point, for example), if you need to remove a measurement, the tool must remain selected and you press the Esc key to remove each measurement you created (from last created to first created).
	Orbit Camera	The Orbit Camera toolbar options allow you to "walk" around the assembly, turn the assembly, or orbit (rotate) around a fixed point (default setting). Walk - Changes the 3D CAD view to create the appearance of walking. Turntable - Allows you to spin the 3D CAD image 360°. Orbit Camera - Allows you to rotate the 3D CAD image around a fixed point. Select the Reset Camera toolbar button to restore the camera view to the default.
	Explode Menu	The Explode menu gives you a slider control to create an exploded view of a 3D CAD assembly where individual parts are separated from the complete assembly as you drag the slider.
	Cutting Plane Menu	The Cutting Plane Menu options allow you to simulate "slicing" a 3D solid or surface with a cutting plane.
	Snapshot	Select the Snapshot toolbar button to create a snapshot of the current 3D CAD view and save the image as a .png file. Select Snapshot. Right-click the 3D CAD image, select Save Image As, select a file location, enter a name for the image, then select Save. Select the Close* button to return to the 3D CAD tab.
	Settings	Select Settings on the toolbar to display a variety of settings for editing 3D images. General tab - Use these options to modify or turn on/off the following settings. General Projection Mode - Displays a 3D CAD object using one of two modes: Orthographic (an object is depicted using parallel lines to project its shape onto a plane) or Perspective (graphically approximates a three-dimensional object on a two-dimensional surface to approximate actual visual perception). Framerate (fps) - The number of frames FactoryLogix displays and renders a 3D CAD image in frames per second (fps) for every second of real time. Hidden Line Opacity (0-1) - Changes the opaqueness of lines in the Hidden Line view. You can set hidden lines from 0-1. Show Backfaces - Toggles the display of backfaces on/off in a 3D CAD image. In a normal view, vectors are drawn from the face center outward from the front. Any normals going away from you indicate a backface (reversed). Show Capping Geometry - Toggles the display of capping geometry On/Off. Enable Face/Line Selection - Toggles the ability to select faces and lines. Selection Honors Scene Visibility - Toggles the ability to make an honors scene visible in a 3D CAD image. Rotate Around Camera Center - When enabled, each time you drag the cursor to rotate the 3D CAD image, the assembly is rotated around the camera's center. Effects Enable Ambient Occlusion Radius - specifies the radius angle used for ambient occlusion. Enable Anti-Aliasing - Toggles anti-aliasing On/Off. (Anti-aliasing smooths jagged edges on curved lines and diagonals.) Enable Bloom - The Bloom effect creates fringes of light extending from the borders of bright areas in a 3D CAD image, providing an illusion of a very bright light overwhelming the camera. Intensity Scale - Specifies the strength of the Bloom filter. Threshold - Specifies the level of brightness to filter out pixels under this threshold level. (The Threshold level is expressed in gamma-space.) Silhouette Edges - Toggles the display of silhouette edges On/Off. Reflection Planes - Toggles the display of reflection planes On/Off. Enable Shadows - Toggles the display of shadows On/Off. Interactive - Turns interactive shadows On/Off. Blur Samples - Sets the blur intensity for shadows. Axis Show Axis Triad - Toggles the display of the 3D axis On/Off. Show Nav Cube - Toggles the display of the Nav cube that shows part faces as you rotate a 3D CAD image. Point Cloud Enable Splats - Toggles splats On/Off. Size - Specifies the size of splats. Mode - Specifies the mode to be used for splats. Enable Eye-Dome Lighting - Toggles eye dome lighting (improves depth perception of the point cloud) On/Off. Color Background Color - Use this option to specify Top and Bottom background colors. Capping Geometry - Use this option to specify Face and Line colors for capping geometry. Selection Color - Use this option to specify colors for image Body, Faces and Lines, Measurement color, and to enable and select a PMI Override Color. Walk tab - Use these options to control the 3D view in a drawing interactively to create the appearance of walking through the model. Walk Mode - Select Keyboard or Mouse. When you select Keyboard, the Navigation Keys and these options are activated: Rotation (Deg/s) - Specifies the rotation (in degrees) for walking the assembly. Walk Speed (cm/s) - Specifies the speed (in centimeters per second) for walking the assembly. Elevation Speed (cm/s) - Specifies the elevation speed (in centimeters per second) for walking the assembly. Field of View (Deg) - Specifies the field of view (in degrees) used while walking the assembly. Enable Mouse Look - In Keyboard mode, shows the cursor to give the appearance of using the mouse while walking. Speed - Specifies the mouse speed when Mouse Look is enabled. Enable Collision Detection - Allows you to check your 3D CAD assembly models so that you can ensure all parts fit correctly and can move as intended. Drawing tab - Use these options to control the colors used for the Background, the Sheet, and the Sheet Shadow for your 3D CAD assembly image. You can also enable or disable the Sheet Background.